Most painters have no problem painting doors in place, but they recommend you lay the door on sawhorses and work horizontally. If you have a paneled door, start with the panels and work from the outside edges in toward the center. "Watch the corners — paint loves to puddle," warns Dixon. While the paint is still wet, lightly "tip off" the panel with an almost dry brush. (Tipping off is pulling the brush over the surface to level out the finish.) When painting the stiles (vertical) and rails (horizontal) just follow the grain of the wood. When the grain changes abruptly, for instance, where the rail meets the stile, don't stop your brush stroke — you'll only leave a lump of paint. Apply paint across the joint with a full stroke, and then tip off the overlapping section by pulling the brush in the direction of the grain. "Make sure the door is dry before painting the opposite side or rehanging it," says Maceyunas. 

A number of details will affect the cost of painting the exterior of your house, such as its size, accessibility and siding type. In many cases though, preparation often has the biggest impact on the bottom line.Your local exterior painting contractor will take a look at the project to determine how extensive repairs and preparation will be and if special equipment, materials or paints are needed to get the job done right.
To get basic measurements, measure the length and width of each wall you want to paint in inches. Multiply the length and height together, and divide by 144. This will give you the square footage for each wall. A gallon of paint typically covers around 400 square feet. In some cases, you may need a primer 2 first, then a single coat of paint, meaning that you may need one gallon of primer and one gallon of paint to cover 400 square feet. However, if the wall requires multiple coats, this will increase the total amount of square footage required, and therefore the amount of paint.
O'Neil patches shallow holes and divots with Ready Patch because it dries fast, sands smooth, and stays flexible. Deep cracks and rotten spots are best repaired with two-step epoxies, such as those made by Advanced Repair Technology. (For a step-by-step instructions, see Repairing Rot with Epoxy.) The days of using polyester auto-body fillers on wood are over. "They cure too hard," says Portland, Oregon–based painting contractor Kathleen George. "They look good at first, but then they peel away."
We had a bad experience with an interior painter years ago, with the crux of the problem being him overcharging us at the end for "extra work" he didn't anticipate. One thing I'd strongly recommend is making sure it's in the contract that any additional work or growth work is estimated and communicated to the owner as soon as it is identified, otherwise the owner is not liable to pay it at the end.
At Five Star Painting, we offer free price estimates, so there’s no reason to hesitate! Our house painting contractors know what they’re doing, and they do it well! Call our residential painting experts today at (888) 261-3633 to receive your free estimate or to schedule a home visit. Use our online scheduler to pick the date and time of your consultation.
Painters often tint primer close to the color of the top coat, but Wallis thinks that's a recipe for "holidays," or missed spots. Instead, he tints his primer a contrasting color. "If I can see the color coming through, I know I need to apply more paint," he says. On the cottage shown in this story, he chose a gray-blue primer to go under a peach top coat.

Home Painter Company


Consider purchasing supplies personally to save money. Ask the painter for a bid that separates labor and materials. Then explain that you'll purchase the materials and ask for a list of exactly what will be needed to complete the job. Caulking, for example, is an extra supply commonly used to fill any cracks or damaged areas in your walls -- and one that might be overlooked in an incomplete list.


Sanding not only feathers out chipped paint but also provides "tooth" for the next coat of paint. For glossy trim, use a sanding sponge rather than sandpaper. Sponges mold to the shape of the trim and last longer than paper. When applying latex over alkyd paint or when he is not sure of the original finish, Brian Doherty, a painter in Richmond, Virginia, follows the hand-sanding with liquid sandpaper to make sure the surface is completely deglossed to prevent incompatibility problems. "I've seen homes where latex was used on oil-painted trim, and the paint started to peel in less than a year," says Doherty.

Because of our wet/cold weather, another painter was booked out through August as of May 7th, 2016.  Anyone even thinking about a VA loan refi should get estimates for painting and pest inspections BEFORE starting on the loan paperwork, otherwise you will have difficulty getting painting and inspections done in a timely manner (and it is my understanding this is common with VA loans.)  
Here is where this affects you as a consumer. You select a painter with a contract that says 2 coats, $500 down. You give the company the deposit and pick your colors a couple of days before the project starts. The painter goes to the store with your colors and figures out they are deep base. He (or she) not only needs to charge you more for the paint, but he also needs to charge you for a dark gray primer coat. Ninety nine percent of the time that primer coat is going to be really, really expensive since you already gave a deposit.

My wife and I just painted the interior of our house with about 6-8 gallons, of $30+ per gallon (meaning the good stuff, non-diluted) with absolutely fantastic results. However we just paid an average of $5 per gallon. Reason...all big box stores have paint, set aside, that has been mixed but not picked up by the customer. They need to sell it quick and if you're not in a hurry (you know well in advance that a room or two need painting and it's not like the roof leaking and needs an immediate fix) you can go to each store when you need other supplies or food, like Walmart (when convenient, driving 20 miles to each is not worth it) and over the course of a month or two, pick out some very nice colors of quality paint. We found perfect colors...not saying they were our first choice but when we opened the can, very nice and some even better than our original picks. Cost to paint the entire house was about $100, with all materials included, period. We had it on the market for a few months to sell, didn't sell, painted the rooms, got 2 offers the day after we finished, took the best one and never looked back.

The last big decision is how to apply the paint. Most pros use paint sprayers because they're fast, but in inexperienced hands a high-powered sprayer can leave drips, thin coats, and a mist that may land on many things other than your siding. If you do hire a painter who uses a sprayer, make sure he is meticulous about removing, covering, or masking off everything in the area that might get hit with overspray: gutters, roofs, windows, shrubbery, walkways, cars—you name it.
Because of our wet/cold weather, another painter was booked out through August as of May 7th, 2016.  Anyone even thinking about a VA loan refi should get estimates for painting and pest inspections BEFORE starting on the loan paperwork, otherwise you will have difficulty getting painting and inspections done in a timely manner (and it is my understanding this is common with VA loans.)  
You can watch all the DIY YouTube videos you want and still not achieve that elusive, professional finish. Certain skills can't be taught; instead, they're learned through experience and practice. The painting professionals on the Handy platform know the tricks of the trade that'll leave your home looking its best. It's skills like these that allow your residential home painters to get your job done quickly and cheaply, without compromising on quality. Book your home painters through Handy, and you'll be connected with top-rated, reviewed professionals in your area. Painting and decorating might look easy on an online tutorial, but it can cost you an awful lot of time and money to discover that it isn't. Don't gamble with the way your house looks: book a professional house painter through Handy today and achieve the look you deserve.
The cost to paint metal siding -- most commonly aluminum and galvanized steel -- will depend on a variety of factors. In some instances, a simple cleaning will suffice to prepare metal siding for painting. In worst cases, painting professionals will need to repair metal that is rusted, damaged or missing pieces due to climate conditions. In the case of severe damage, a professional will have to remove the old finish and paint to get to the original layer, which will add on to the final price. When you add the actual painting of the metal siding, you might be looking at a final bill between $400 (~250 sq. ft.) and $1,500 (~1,000 sq. ft.).
Some proposals simply say to paint the walls and ceiling and never specify the number of coats to be applied. If the colors are similar enough, it's possible to get away with one coat of paint and not discount your pricing. No matter how hard you try, tiny, pin-sized air holes will pop exposing the original walls. This may not bother you if you can't notice it, but principally speaking you should have paid your painter less for the work.
Because of our wet/cold weather, another painter was booked out through August as of May 7th, 2016.  Anyone even thinking about a VA loan refi should get estimates for painting and pest inspections BEFORE starting on the loan paperwork, otherwise you will have difficulty getting painting and inspections done in a timely manner (and it is my understanding this is common with VA loans.)  
Ideally, you want as much paint on the brush as you can control without making drips or blobs. To do this, Doherty dips his brush about 1 1/2 inches into the paint, then taps (not wipes) each side of the brush against the side of the can. Tapping knocks off the drips and forces the paint into the bristles. "The brush releases the paint just like a fountain pen," he says. Weeks agrees, saying, "Just be sure to keep your brush moving, or it'll start to drip." For more delicate work, such as when you're painting trim or window sash, you'll want less paint on the brush. Doherty again dips and taps his brush, but this time he also scrapes the sides against his can. "The outside bristles are drier and easier to manage," he says, "but there's still plenty of paint on the brush."
I turn away any job when the client refuses to pay anything up front. It sends a red flag. I also charge a scheduling fee which is non-refundable. I get 33 percent when I show up and begin work. Another percentage halfway through, and the balance upon completion after client is satisfied. There needs to be skin in the game for both parties as a measure of good faith. If you are dealing with a reputable company (did your due diligence, right?) why wouldn't you want to pay something as work progresses? We do this not only because we love to paint but we require cash flow to stay in business. There is not always 'money in the bank' as you suggest. It's tough these days. The suggestion buy 'Kim' 'Never pay a contractor a deposit' is nonsensical.
Here is where this affects you as a consumer. You select a painter with a contract that says 2 coats, $500 down. You give the company the deposit and pick your colors a couple of days before the project starts. The painter goes to the store with your colors and figures out they are deep base. He (or she) not only needs to charge you more for the paint, but he also needs to charge you for a dark gray primer coat. Ninety nine percent of the time that primer coat is going to be really, really expensive since you already gave a deposit.
Interesting information! We just got scammed in White Stone, Virginia... we chose the same color, but went from a flat to an eggshell finish. I wasn't available to stand over the painter while he painted. For such a detailed job, I marveled at how quickly he finished the project! After he was paid for the job, we discovered all he did was roll paint across the walls and close to the crown, baseboards and detailed trim around windows and doors leaving about an inch or so of the flat finish. By using the same color, he didn't even do the job he was paid to do, which explained why he could finish the job so quickly. By using the same color... he got lucky and passed it off as a completed job not bothering to paint to and cut in around the trim. Upon further evaluation of our walls we could see exactly where he stopped because we could see the difference between the flat and eggshell finishes. There are walls he didn't even bother to paint. Then where he did paint near the crown when we were in the room watching ... he hit the crown moulding and tried to tell us it was already there... and tried to sell us on painting the crown moulding. I am so disgusted and upset!! He'll be hearing from us to rectify the situation.
When you’re ready to tackle your next paint project, we offer an amazing choice of colors from top paint brands, at the best price, and expert know-how to help you do the job right. Whether you’re making a colorful update to the interior or exterior of your home or working on a unique DIY project, you can really pour on the creativity with our unmatched selection of paints and exterior stains, craft supplies like chalkboard paint, stencils, glitter, or even glow in the dark spray paint. You should also check out our paint project and buying guides as well as The Home Depot Blog for current paint trends, popular color palettes and paint craft ideas. For all your painting needs, small and large, we’ve got you covered at The Home Depot.
Good contracts include descriptions of prep work and repairs; paint specs by brand name, type, color and product number; the number of coats; and a full description of the work, including frequently omitted items such as cabinet interiors and shutters. Minimize delays by specifying that, weather permitting, work will be continuous. Get a payment schedule that minimizes the down payment — the more payment you can withhold until the end, the more leverage you'll have to get the job done well and per your specifications. Insist that contractors provide proof that they carry both general liability and workers' compensation coverage.
What is the definition of a painter? Is it someone that can simply pick up a brush? Perhaps a painter is someone that climbs ladders while applying paint for a living? An experienced painter may have a few larger tools and own what appears to be a paint van/truck. In many cases, a painter maybe a college student or older person doing a few projects during the summer, on the side, weekend work or attempting to paint a few local homes for extra cash? Maybe this describes exactly what you are looking for? Or, does it sound like something you want no part of? Chances are, if you seek quality, you would likely not hire this person – right? You may ask – what’s the difference? A painter is a painter! Right?
FIRST: Unless you can stay in business painting 1 bedroom at a time for $500-$1000, which you can't, then you will be taking on several thousand dollar contracts that require thousands in Labor and Materials to fulfill the order. Multiply that by 3-4 jobs at one time or in our case 15-20 jobs at a time, YOU NEED TO TAKE DEPOSITS!!! It is horrible business not to take deposits. There are many jobs where its not possible to get a deposit and that is built into or pricing accordingly. If we are not getting a deposit, there is a finance charge built in, contractors are not banks. If you don't have a good feeling about a deposit, your hiring the WRONG CONTRACTOR. Hire people you know or well established businesses.

Contracting is not conducted very often. Or, is it? What about your internet or television provider? How about a restaurant? Are we not contracting a service? Other than hunger, the attraction of the food or the ambiance – ask yourself, what inspired enough interest for you to check that particular restaurant out? Maybe it was word of mouth, good reviews, a good sanitation score, a clean atmosphere, the professional service, the quality of the food, maybe being close by or locally sourced food also helped? While you were considering all these factors – little did you know – you were qualifying and researching before you chose to give that particular restaurant your business. Most dinners cost under $50 per person. Why wouldn’t we take the additional steps needed to qualify our potential contractors for projects that typically cost much more??
Contracting is not conducted very often. Or, is it? What about your internet or television provider? How about a restaurant? Are we not contracting a service? Other than hunger, the attraction of the food or the ambiance – ask yourself, what inspired enough interest for you to check that particular restaurant out? Maybe it was word of mouth, good reviews, a good sanitation score, a clean atmosphere, the professional service, the quality of the food, maybe being close by or locally sourced food also helped? While you were considering all these factors – little did you know – you were qualifying and researching before you chose to give that particular restaurant your business. Most dinners cost under $50 per person. Why wouldn’t we take the additional steps needed to qualify our potential contractors for projects that typically cost much more??
According to the Bureau of Labor Statistics, 45 percent of all painters are self-employed, though that number may be slightly higher if companies hire freelancers or self-employed painters as part of their team. The price that painters charge for their services is largely dependent on their association and whether the job is completed in the warmer or colder months (painters often charge more in the summer and less in the winter, given demand and other factors). More information regarding painter rates and associated factors is included below.

I was a painting contractor for many years and never asked for a deposit upfront. A good contractor should have great credit with his suppliers and an even better contract if the deal should go south before the job is done. Get to know your customer and explain how each paint covers so they understand fully before you have to apply 3 or 4 coats. If you didn't bid your job right and the client has already signed the contract then that is on you not the client. Yes I haven had to eat the difference but the client was happy and a return customer for years so I made up for it.

Before the scrubdown, protect nearby plants by misting their leaves and saturating the surrounding soil with water, pulling them away from the house, and shrouding them in fabric drop cloths. (Plants will cook under plastic.) Lay more drop cloths along the base of the walls to collect any falling paint debris. Walls should be wet down before getting scrubbed, then washed with a gallon of water mixed with 1 cup chlorine bleach and 1 cup of either a concentrated, phosphate-free cleaner, such as a trisodium phosphate (TSP) substitute, or Jomax House Cleaner. Working in sections, from the bottom to the top, will avoid streaks. Be sure to rinse walls well before the solution dries. Wood siding and trim should be ready to paint after a day or two of dry weather.
Spills and spatters happen, regardless of how careful you are. It’s a lot easier to pre- pare for them than to wipe them out of your carpeting or off your wood floor later. All it takes is canvas drop cloths in your work area (a 4-ft. x 15-ft. cloth costs $15). The thick canvas stays in place, so you don’t need to tape it, and you can use it to cover any surface. Plastic drop cloths are slippery to walk on or set a ladder on and don’t stay in place. Even worse, paint spills on plastic stay wet, and they can end up on your shoes and get tracked through the house. Canvas is slippery on hard floors, so rosin paper ($10 for 400 sq. ft. at home centers) is better over vinyl, tile and hard- wood. Tape the sheets together and to the floor to provide a nonslip surface.

OF the different type of customers there are at least two: cheap charley's and people who want great results. I agree the need for wall repair is critical to the end results. Most critical is for the customer to be told ahead that the walls are going to need exactly what is needed. This means the contractor must look, touch, examine the walls for defects and needed work. I've been a building manager for 40 years and seen a few paint jobs. Typically a contractor does a lot of talking about how expert he is, but the guys who walk through with note pads, iPads, examine, measure, point things out, explain and recommend are the ones I will deal with. It confirms if they know what the business. Nobody likes the workers to show up and when you talk about the job they're going to do they know nothing but they we were told to be here. Their boss who bid the job doesn't supervise - a big no no around here. Nobody likes surprises or worse, at the end of a job that's not right getting a bunch of little kid excuses. Contractors that do not like the customer to be around looking at the progress don't get the job.

×