The cost to paint metal siding -- most commonly aluminum and galvanized steel -- will depend on a variety of factors. In some instances, a simple cleaning will suffice to prepare metal siding for painting. In worst cases, painting professionals will need to repair metal that is rusted, damaged or missing pieces due to climate conditions. In the case of severe damage, a professional will have to remove the old finish and paint to get to the original layer, which will add on to the final price. When you add the actual painting of the metal siding, you might be looking at a final bill between $400 (~250 sq. ft.) and $1,500 (~1,000 sq. ft.).
When you refinish your existing cabinet doors, you get a whole new look without the astronomical costs normally associated with a kitchen remodel. It’s a much smarter way to update your space, especially if your cabinets are still in good condition. It doesn’t make sense to throw out perfectly good materials, just because you’re tired of the color.
Specialty painting by the hour costs between $40 to $50 on average. Paint might range between $75 to $90, costing an additional $40 to $50 per hour. The painter's skill and experience are also determining factors in the cost of specialty painting. While a freelance artist might charge $25 to $30 an hour, a very skilled professional might charge $80 or more. Some painters might also charge $60 or more for a consultation. Trompe l'oeils, in particular, will run on the expensive end of the price spectrum. Return to Top
Before the scrubdown, protect nearby plants by misting their leaves and saturating the surrounding soil with water, pulling them away from the house, and shrouding them in fabric drop cloths. (Plants will cook under plastic.) Lay more drop cloths along the base of the walls to collect any falling paint debris. Walls should be wet down before getting scrubbed, then washed with a gallon of water mixed with 1 cup chlorine bleach and 1 cup of either a concentrated, phosphate-free cleaner, such as a trisodium phosphate (TSP) substitute, or Jomax House Cleaner. Working in sections, from the bottom to the top, will avoid streaks. Be sure to rinse walls well before the solution dries. Wood siding and trim should be ready to paint after a day or two of dry weather.
Some proposals simply say to paint the walls and ceiling and never specify the number of coats to be applied. If the colors are similar enough, it's possible to get away with one coat of paint and not discount your pricing. No matter how hard you try, tiny, pin-sized air holes will pop exposing the original walls. This may not bother you if you can't notice it, but principally speaking you should have paid your painter less for the work.
Contracting is not conducted very often. Or, is it? What about your internet or television provider? How about a restaurant? Are we not contracting a service? Other than hunger, the attraction of the food or the ambiance – ask yourself, what inspired enough interest for you to check that particular restaurant out? Maybe it was word of mouth, good reviews, a good sanitation score, a clean atmosphere, the professional service, the quality of the food, maybe being close by or locally sourced food also helped? While you were considering all these factors – little did you know – you were qualifying and researching before you chose to give that particular restaurant your business. Most dinners cost under $50 per person. Why wouldn’t we take the additional steps needed to qualify our potential contractors for projects that typically cost much more??
A number of details will affect the cost of painting the exterior of your house, such as its size, accessibility and siding type. In many cases though, preparation often has the biggest impact on the bottom line.Your local exterior painting contractor will take a look at the project to determine how extensive repairs and preparation will be and if special equipment, materials or paints are needed to get the job done right.
Lap marks are those ugly stripes caused by uneven layers of paint buildup. They occur when you roll over paint that’s already partly dry. (In warm, dry conditions, latex paint can begin to stiffen in less than a minute!) The key to avoiding lap marks when doing DIY wall painting is to maintain a “wet edge,” so each stroke of your roller overlaps the previous stroke before the paint can begin to dry.
Your home is your most important asset and maintaining it is vital in upholding and increasing its value. As a full-service painting company, Home Works Painting will provide you with a superior professional painting experience. Our services include interior/exterior painting, drywall repair/installation, wood replacement, pressure washing, and color consulting. We stand behind our work by offering a six year warranty.
These are some fantastic questions to ask and I particularly like the one that is concerned about safety for the painters. After all, if you have a large home and you’re hiring them to paint the exterior of that home then they’ll likely be on scaffolding. Because of that, you need to make sure that the contractor not only provides appropriate safety training, but has the correct liability insurance as well.
Ask companies to include all details in writing. Although that sounds simple enough, too many contractors submit offers such as "paint house for $5,000." A friendly contractor may offer a reassuring handshake and promise that the crew will take care of all the details — starting on time, working every day, cleaning up, etc. That's great, but why not include each point in the proposal? If it's a challenge to get a written description of labor, materials and other details, things will probably get worse when the work starts.
To industrial and institutional. I also own and operate a professional painting company of elite painters ONLY 5 ELITE PAINTERS, and pay them good money for being elite. Less is better in my opinion.The fact is this a homeowner and a painting company owner can both be taken advantage of by hustlers and liars and amateurs posing as pros. I have had many laborers tell me they can paint. " Oh yes sir I can paint, I'm a painter of 8 years. Yes sir I can cut a straight line." Some people will say and do anything to get a buck. If yoir on the job to see their rookie mistakes you may have time to save your reputation before disaster ensues and fire them on the spot. As a painting Company owner if your not on the job with your crew at least 3 out of 6 days every week your taking a huge risk of damaging your reputation and losing the respect of your team. Homeowners want to deal with you or the crew boss (jobs site supervisor) not "the painter". Many things I have read are right on. Painters for the most part will milk a clock for all they can and still do a good job. But amateurs will leave your projects in shambles and the only ones to pay for it is the contractor and the homeowners. But an elite painter and crew will try to complete a project as quickly as possible and move on to the next one. They understand bonuses, incentives, and promotions. My company provides the opportunity for a homeowner to meet each member of the crew and shake there hand on day one. There is also a differentiation between the crew boss and the crew by the uniforms they wear. Should the homeowners have any issue at all they know exactly who to go to to get results. This eliminates the age old problem of who screwed up? I have found that by me putting on my whites and giving my crew the opportunity to out do themselves on each project it ignites competition, pride in skill, and excellent commraderie amongst the team. We all hold each other accountable. Choose your contractor by the crew not the owner. The crew is a direct reflection of the Company owner. No room for rookies on fine finish painting. Go pro for painting and you won't regret it. With that being said homeowners should always remember that you get what you pay for. With paint and services. In most cases it will be well worth a few extra bucks to get elite results. Never go with the cheapest bid there is always a reason why it's so low.
Inspect the surface area for holes, cracks or other problems and apply acrylic caulk to fill them in. Use a putty knife to smooth out the caulk and remove any excess to prevent bumps. For particularly thin or narrow crevices, you may have to use your finger to smooth out the caulk. Caulk contracts and shrinks, so apply a second layer once it's dried.