Dave, you said it best! Every pro painting contractor truly worth their salt would and should cut and paste exactly what you say here about where customary and legitimate practices and expectations should be in regards to what customers should expect from contractors and how contractors should professionally deal with their customers. By the way, Dave, if you work in the Atlanta area, I would like to hire you! Thank you for your valuable advice!


Inspect the surface area for holes, cracks or other problems and apply acrylic caulk to fill them in. Use a putty knife to smooth out the caulk and remove any excess to prevent bumps. For particularly thin or narrow crevices, you may have to use your finger to smooth out the caulk. Caulk contracts and shrinks, so apply a second layer once it's dried.
Lap marks are those ugly stripes caused by uneven layers of paint buildup. They occur when you roll over paint that’s already partly dry. (In warm, dry conditions, latex paint can begin to stiffen in less than a minute!) The key to avoiding lap marks  when doing DIY wall painting is to maintain a “wet edge,” so each stroke of your roller overlaps the previous stroke before the paint can begin to dry.
Sand the trim with a fine-grit sanding sponge. Sponges get into crevices where sandpaper can’t go and let you apply even pressure. Then apply the first coat of paint, let it dry at least 24 hours, lightly sand it again for a completely smooth surface, and apply the second coat. After each sanding, vacuum the trim, then wipe it down with a tack cloth to remove the dust.
The cost to paint metal siding -- most commonly aluminum and galvanized steel -- will depend on a variety of factors. In some instances, a simple cleaning will suffice to prepare metal siding for painting. In worst cases, painting professionals will need to repair metal that is rusted, damaged or missing pieces due to climate conditions. In the case of severe damage, a professional will have to remove the old finish and paint to get to the original layer, which will add on to the final price. When you add the actual painting of the metal siding, you might be looking at a final bill between $400 (~250 sq. ft.) and $1,500 (~1,000 sq. ft.).

Some contractors work on time and material others on a firm contract. I would never hire the former and am leary of the latter. A contractor may low-ball a bid to get the job planning to make a killing on change orders. If you say good morning to them, they charge you extra for that. If the contract is not very, very specific and extensively fleshed out or if they display their change order schedule prominently on top, show them the door.


I used to work at Sherwin Williams. The best thing to do is specify that you will purchase your own paint. If the painter objects strenuously, he was plaanning on making money in the ways this article outlines. You might pay a few dollars more for paint, but you will have control of the quality of what goes on your walls. Never skimp on paint quality.


I would never suggest that one of my clients buy their own paint because A . They will pay an average of $20 to $30 more per gallon which could add up to $1,000 or more to a full repaint B. most times I'm in the paint store homeowners are kind of pushed to the foreground as they handle all the contractors in the store and C. Paint is heavy, takes up a lot of room needs to be left in it clean dry area and I hate to put a client to work when they are trying to hire me to do their job.

If you hire a contractor for a painting job, you’ll want some assurances in the form of guarantees or warranties.  Knowing the importance of warranties, some companies even give unrealistically long warranties such as 10 years, 20 years or even lifetime warranties. The sad fact is that most of these companies will be out of business long before their warranties expire. So what is a realistic warranty that you can trust? Here’s what you should look for in a great warranty:
Estimates are one of the most important tools to help you land the next job. During our most recent webinar series on estimating, Fred Yarur of PEP (Painter’s Estimating Program) outlined 10 foundational principles to support effective estimating procedures. Use estimate tools. These enhance your ability to make informed decisions. Estimating is the process of […]
Generally speaking, in order to be considered a contractor there are standards and minimum requirements that must be met. But a professional painting contractor provides so much more than what’s standard! As customers, it can be hard to come to terms or articulate exactly what it is that we are looking for. In many cases, we are simply not well researched or informed enough to make the best decisions based on our needs. But you really can’t afford to contract the wrong company. Not doing your homework may leave you under the assumption that you have hired a painting contractor, when in reality you have just hired a painter. When you hire just a painter, you as the homeowner have taken all responsibilities of a contractor. Now all the responsibilities, liability and management is on you!
These days, it seems like anyone with a paintbrush and a business card can call themselves a painting contractor. Homeowners who are most likely to be taken in by these unscrupulous “painters” are those who are focused on cost and cost alone. With painting, like anything else in life, you typically get what you pay for. If the painting contractor you are considering cannot answer these ten questions, proceed at your own risk. If they answer all ten satisfactorily, then you know you’ve found a great great professional contractor to work with. 

Painting contractors must also carry out administrative and marketing duties. They prepare final accounts for customers based on the original estimates and any additional work. They analyze the cost of the job compared with the estimate to calculate their profit. They market their business through activities such as setting up websites, asking customers for references or contacting property maintenance companies with details of their services.
I agree with JHs. If there is no new color on it at all, just talk to the painter about it, if it was an honest mistake (which can happen very easily while painting) your painter should have no problem fixing it. However, in my years of experience, it is not unusual for 2 coats of door paint (good quality) not to cover very well at all. I once painted a red door 7 times, plus a tinted prime coat before I found the door to be a solid color.
Unless you like textured walls, don't paint over dust. Wash the walls with trisodium phosphate (TSP) or a mild cleaner, like Jasco's TSP No-Rinse Substitute. For smoke-stained walls, Toto uses a 50/50 solution of bleach and water. To clean a wall, use two buckets. Load up your rag or sponge from your cleaning-solution bucket, and scrub. Before redipping, rinse the sponge in a second bucket filled with clean water.
Even if you think you'll probably do the job yourself, it's good preparation to seek estimates from professional home painters, whether your painting the exterior or interior of your home. Then you'll have a financial point of comparison and you may benefit from what a home painting contractor has to say about the condition of your home, color choices and types of paint available. Let the painter make his pitch for a professional job before you decide what to do. You can still opt to do it yourself while having learned something worthwhile.
I am getting quotes to paint the exterior of a 2,500 sq ft split levei home that just had all new windows and pre-primed Hardiplank installed 3 months ago. the quotes are up to $2,500 different ranging from power wash,prime again 3 coats of paint to no powerwash needed so soon and one coat of paint.. All quotes include trim. One includes complete replacement of 80 feet facia boards another just 40 feet.
Not all people live where they can hire a painting contractor, like you describe. People who live in small towns can only hire painters who have a very small business, and do two or three paint jobs per week. In this case, you do have to be very careful, when you hire a painter, as we have several, in our area, who are out to make a fast buck anyway they can.
So why not just paint your own home. I'm not a painter, so my wife and I take our time, buying the paint and supplies, and doing our own painting. Yes, we need to tape, and it's not perfect, but we get the satisfaction of seeing our completed work. Get the supplies, sliders for your furniture, and patience and go for it. That way YOU have control over the entire project.
Hello, I have a sad situation to share -- a friend of mine who is a very good painter, experienced too, fell off a tall ladder that did not have "boots" on it. (I've never seen those.) Anyway, do you think he should have asked for boots before painting? Possibly it was a situation where he was shy to ask because he wanted the job... (I don't know all the details.)
Here is where this affects you as a consumer. You select a painter with a contract that says 2 coats, $500 down. You give the company the deposit and pick your colors a couple of days before the project starts. The painter goes to the store with your colors and figures out they are deep base. He (or she) not only needs to charge you more for the paint, but he also needs to charge you for a dark gray primer coat. Ninety nine percent of the time that primer coat is going to be really, really expensive since you already gave a deposit.
Sand the trim with a fine-grit sanding sponge. Sponges get into crevices where sandpaper can’t go and let you apply even pressure. Then apply the first coat of paint, let it dry at least 24 hours, lightly sand it again for a completely smooth surface, and apply the second coat. After each sanding, vacuum the trim, then wipe it down with a tack cloth to remove the dust.
Stucco is a specialized material that requires extensive preparation work (cleaning, caulking, filling in cracks, etc.). Additionally, paint suitable for rolling or brushing over stucco varies greatly depending on location and climate conditions. Some stucco paint varieties will chip and peel away in certain climate conditions, so painting professionals won't recommend them. These factors make stucco one of the more expensive siding materials to cover. You can expect to pay anywhere from $900 (~500 sq. ft.) to $3,000 (~1,500 sq. ft.) to have stucco revitalized with paint, depending on how much is needed to cover the home exterior.
I agree with Jeff below, these prices are far below what I see on the market in the Portland Or. area. When one uses the term "paint the house" what exactly does one mean? Any fool can buy an airless paint sprayer and put paint on a house. New homes built with fiber cement siding paint clean and easily but older homes built with wood require much prep work.
Another factor to consider is the height and features of your home. An example would be a house completely trimmed in Cement Fiber, which does chalk if you do not purchase the correct paint and apply enough of it. Some houses in Coastal Areas are already on 15+ft Stilts (off ground) and then another 20ft high at times. This requires rental equipment and careful cost estimation based on the difficulty of the overall project, The best advice that I can give is to get several estimates in your area and make a decision a couple of weeks afterwards. You will "weed out" per se the individuals that do not have the patience to finish a project that was started-as well as those who haggle you for payment (sometimes daily) before project is completed. I have heard some wild stories from a lot of Homeowners. Common sense and your intuition will make you aware of anyone that you should not hire.
It is one of our core values to ensure our clients’ dreams for their home comes true. So often, clients come to us for a new coat of paint or a repair but what they really want is so much more. We understand your house is your home and that when it is time for change or for a repair, you want a crew that will take care to make your home look its best.
As you walk through your lighted rooms (preferably day light) see if the new coat has light spots showing the precious paint. This is call "bleeding through". This means that there's only one coat of paint or the paint was diluted or the trasition of colors were from light to dark (or the other way around) and primer was not use or the painter is inexperienced.
Inspect the surface area for holes, cracks or other problems and apply acrylic caulk to fill them in. Use a putty knife to smooth out the caulk and remove any excess to prevent bumps. For particularly thin or narrow crevices, you may have to use your finger to smooth out the caulk. Caulk contracts and shrinks, so apply a second layer once it's dried.
Are you looking for interior house painters that are local, reliable and the best at what they do? Does the idea of painting the walls of your home fill you with dread? If you want to get the best results with minimal fuss, then make Handy your first choice when you need to connect with expert painting contractors. From preparing your interior walls and ceilings to achieving a neat, professional finish, Handy will put you in touch with the right people for the job. Customize your request by specifying your job details, from how many painters you need to how long you’ll need them. We’ll connect you with the painting professionals that suit you best with no compromise on quality.
Thorough preparation is essential to ensure a good finish. Contractors might have to fill cracks or holes and remove old paint if it is badly worn, peeling or flaking. They remove all paint and apply a suitable primer to the bare surface. If the existing paint is in reasonable condition, they clean it and rub it with abrasive material to provide a key for the new paint. On new surfaces, such as bare wood or fresh plaster, they apply a suitable seal, followed by a primer coat.
I’m sure I’d have a mustache full of beer and a stein full of tears, if only I could stand to drink it. I had my first sip of beer at age seven and that was enough to turn me off for life. So…at least there’s chocolate. All that said, we’ve still got a Paint Contractor full of useful and entertaining content—this being our last issue, we wanted to go out classy and take our last chance to profile a great painter and help you into a new year even if we can’t follow.

I am getting quotes to paint the exterior of a 2,500 sq ft split levei home that just had all new windows and pre-primed Hardiplank installed 3 months ago. the quotes are up to $2,500 different ranging from power wash,prime again 3 coats of paint to no powerwash needed so soon and one coat of paint.. All quotes include trim. One includes complete replacement of 80 feet facia boards another just 40 feet.


A painter's rod, or pole, can help you paint ceilings more quickly — no climbing up and down ladders required. And there's no need to stand directly underneath the area you are painting, so you won't catch every wayward splatter. A pole is also great for walls and floors. The pros were split over whether the 4- or 8-foot pole is best for everyday use, but they all agreed that a telescoping rod is the best bet.
YP - The Real Yellow PagesSM - helps you find the right local businesses to meet your specific needs. Search results are sorted by a combination of factors to give you a set of choices in response to your search criteria. These factors are similar to those you might use to determine which business to select from a local Yellow Pages directory, including proximity to where you are searching, expertise in the specific services or products you need, and comprehensive business information to help evaluate a business's suitability for you. “Preferred” listings, or those with featured website buttons, indicate YP advertisers who directly provide information about their businesses to help consumers make more informed buying decisions. YP advertisers receive higher placement in the default ordering of search results and may appear in sponsored listings on the top, side, or bottom of the search results page. 

The PPG logo is a registered trademark and Colorful Communities and We protect and beautify the world are trademarks of PPG Industries Ohio, Inc. © 2019 PPG Industries, Inc. All Rights Reserved. | Legal Notices & Privacy Policies | CA Transparency in Supply Chain Disclosure | Global Code of Ethics | TISC for PPG Architectural Coatings UK Limited | TISC for PPG Industries (UK) Limited | PPG Industries UK Ltd 2017 Gender Pay Gap Report
Before the scrubdown, protect nearby plants by misting their leaves and saturating the surrounding soil with water, pulling them away from the house, and shrouding them in fabric drop cloths. (Plants will cook under plastic.) Lay more drop cloths along the base of the walls to collect any falling paint debris. Walls should be wet down before getting scrubbed, then washed with a gallon of water mixed with 1 cup chlorine bleach and 1 cup of either a concentrated, phosphate-free cleaner, such as a trisodium phosphate (TSP) substitute, or Jomax House Cleaner. Working in sections, from the bottom to the top, will avoid streaks. Be sure to rinse walls well before the solution dries. Wood siding and trim should be ready to paint after a day or two of dry weather.

The last big decision is how to apply the paint. Most pros use paint sprayers because they're fast, but in inexperienced hands a high-powered sprayer can leave drips, thin coats, and a mist that may land on many things other than your siding. If you do hire a painter who uses a sprayer, make sure he is meticulous about removing, covering, or masking off everything in the area that might get hit with overspray: gutters, roofs, windows, shrubbery, walkways, cars—you name it.
×