Contracting is not conducted very often. Or, is it? What about your internet or television provider? How about a restaurant? Are we not contracting a service? Other than hunger, the attraction of the food or the ambiance – ask yourself, what inspired enough interest for you to check that particular restaurant out? Maybe it was word of mouth, good reviews, a good sanitation score, a clean atmosphere, the professional service, the quality of the food, maybe being close by or locally sourced food also helped? While you were considering all these factors – little did you know – you were qualifying and researching before you chose to give that particular restaurant your business. Most dinners cost under $50 per person. Why wouldn’t we take the additional steps needed to qualify our potential contractors for projects that typically cost much more??
The cost to paint metal siding -- most commonly aluminum and galvanized steel -- will depend on a variety of factors. In some instances, a simple cleaning will suffice to prepare metal siding for painting. In worst cases, painting professionals will need to repair metal that is rusted, damaged or missing pieces due to climate conditions. In the case of severe damage, a professional will have to remove the old finish and paint to get to the original layer, which will add on to the final price. When you add the actual painting of the metal siding, you might be looking at a final bill between $400 (~250 sq. ft.) and $1,500 (~1,000 sq. ft.).
Pros prefer 5-gallon buckets with a roller grid to roller pans. They hold more paint than pans and, says Doherty, "It's tougher to tip over a bucket." A bucket also lets you box, or mix, two or three cans of paint to avoid color discrepancies. To use a bucket and grid, dip the roller a quarter of the way into the paint and run it over the ramp to work the paint into the nap.
I do not mean to come off with an edge, however, this is an article for people hiring low bid, uninsured, one man band painters out to "hustle" a buck. Hire reputable, established companies or hire someone you know or have a strong referral from. If you are arguing over watered down paint, ticky, tacky deposits, buying your own supplies, you have hired the wrong guy.
I would not recommend this company for the following reasons:1. Original appointment was very specific to them on what was needed and to take photos for 3 apartment unit plumbing fixture repairs. One unit had a bathroom tub/shower backup.2. No photos taken, 3 trips later and only 1 unit completed to satisfaction. (Backup) 3. Other faucets unable to find on line with their suppliers and repair 4. Had to find another plumbing company to complete the jobs. 5. Invoicing had to be redone as not in detail of job address for tax purposes 6. Bad communication throughout the project process with their internal customer service. Their technician and project manager ordering parts. 7. For the back up. Did not bring out correct snake on both trips and had to replace lines as too small to break through backup. Costing over $800 for 3 trips just to complete that situation out. 8. Ordered the wrong parts when 2nd trip out since no photos taken to confirm what was needed. Very dissatisfied and will never ask them to work in any of our rental properties again.
I'm an architect and my firm routinely specifies interior finishes for projects so I thought I'd contribute a professional's perspective on the issue of how many coats of paint are deemed "acceptable". The fact of the matter is the average consumer usually isn't a paint expert and can't be expected to know about all the factors that impact coverage. That knowledge is considered "means and methods" and in a court of law, the responsibility lies with the painter or general contractor, not the consumer. What the consumer should be concerned about is the final result-does it look good and is it what you expected? The simplest way to communicate this to your painter is to stipule in your written agreement that the number of coats will be "as required to cover". That way all the guess work about what kind of primer, how many coats, how color affects the scope of work, etc., is removed from the consumer's responsibility and resides where it belongs-with the professional. In the contract that's why retention is always a good idea-typically 10% is withheld from payment until the job is completed to the satisfaction of the customer. Of course in return you as the customer have to be reasonable about what constitutes a completed job. Just my $.02.