Inspect the surface area for holes, cracks or other problems and apply acrylic caulk to fill them in. Use a putty knife to smooth out the caulk and remove any excess to prevent bumps. For particularly thin or narrow crevices, you may have to use your finger to smooth out the caulk. Caulk contracts and shrinks, so apply a second layer once it's dried.
You are right on with this - why do people leave switch plates on when it's just so easy to take them off? Another thing that happened to us - we had the popcorn ceiling taken off and the ceiling painted white. When the job was done and I later went to change out all the fixtures/fans, they had left every fixture in place, so there was a large patch of popcorn and unpainted ceiling left behind - it just didn't dawn on me to specify that they take those down before scraping and painting. It was kind of a mess.

I am getting quotes to paint the exterior of a 2,500 sq ft split levei home that just had all new windows and pre-primed Hardiplank installed 3 months ago. the quotes are up to $2,500 different ranging from power wash,prime again 3 coats of paint to no powerwash needed so soon and one coat of paint.. All quotes include trim. One includes complete replacement of 80 feet facia boards another just 40 feet.


Our team of industrial, commercial & residential paint contractors have many years of experience working on projects of all sizes. All projects are managed and staffed by in-house professional employees from start to finish. With our attention to detail and commitment to excellent customer service, you can be assured that your project will be successfully completed on time and within your budget.

To get basic measurements, measure the length and width of each wall you want to paint in inches. Multiply the length and height together, and divide by 144. This will give you the square footage for each wall. A gallon of paint typically covers around 400 square feet. In some cases, you may need a primer 2 first, then a single coat of paint, meaning that you may need one gallon of primer and one gallon of paint to cover 400 square feet. However, if the wall requires multiple coats, this will increase the total amount of square footage required, and therefore the amount of paint.
A thorough scrubbing is a must before painting any exterior surface. It removes the dirt and broken-down paint residues that keep fresh coats from adhering and gets rid of mildew that grows on paint in all but the most arid climates. Most contractors clean with pressure washers, but in the hands of someone unfamiliar with the equipment, these can gouge wood, shatter glass, and drive water behind siding and trim. Using a hose, a pump sprayer, and a scrub brush is slower but safer, and just as effective.

Unless you like textured walls, don't paint over dust. Wash the walls with trisodium phosphate (TSP) or a mild cleaner, like Jasco's TSP No-Rinse Substitute. For smoke-stained walls, Toto uses a 50/50 solution of bleach and water. To clean a wall, use two buckets. Load up your rag or sponge from your cleaning-solution bucket, and scrub. Before redipping, rinse the sponge in a second bucket filled with clean water.

I’m sure I’d have a mustache full of beer and a stein full of tears, if only I could stand to drink it. I had my first sip of beer at age seven and that was enough to turn me off for life. So…at least there’s chocolate. All that said, we’ve still got a Paint Contractor full of useful and entertaining content—this being our last issue, we wanted to go out classy and take our last chance to profile a great painter and help you into a new year even if we can’t follow.
Here is where this affects you as a consumer. You select a painter with a contract that says 2 coats, $500 down. You give the company the deposit and pick your colors a couple of days before the project starts. The painter goes to the store with your colors and figures out they are deep base. He (or she) not only needs to charge you more for the paint, but he also needs to charge you for a dark gray primer coat. Ninety nine percent of the time that primer coat is going to be really, really expensive since you already gave a deposit.
Inspect the surface area for holes, cracks or other problems and apply acrylic caulk to fill them in. Use a putty knife to smooth out the caulk and remove any excess to prevent bumps. For particularly thin or narrow crevices, you may have to use your finger to smooth out the caulk. Caulk contracts and shrinks, so apply a second layer once it's dried.
I would never suggest that one of my clients buy their own paint because A . They will pay an average of $20 to $30 more per gallon which could add up to $1,000 or more to a full repaint B. most times I'm in the paint store homeowners are kind of pushed to the foreground as they handle all the contractors in the store and C. Paint is heavy, takes up a lot of room needs to be left in it clean dry area and I hate to put a client to work when they are trying to hire me to do their job.
Before the scrubdown, protect nearby plants by misting their leaves and saturating the surrounding soil with water, pulling them away from the house, and shrouding them in fabric drop cloths. (Plants will cook under plastic.) Lay more drop cloths along the base of the walls to collect any falling paint debris. Walls should be wet down before getting scrubbed, then washed with a gallon of water mixed with 1 cup chlorine bleach and 1 cup of either a concentrated, phosphate-free cleaner, such as a trisodium phosphate (TSP) substitute, or Jomax House Cleaner. Working in sections, from the bottom to the top, will avoid streaks. Be sure to rinse walls well before the solution dries. Wood siding and trim should be ready to paint after a day or two of dry weather.
"There's wisdom in a multitude of counsel" {Bible Book of Wisdom/Proverbs} I thank you all I learned so much here not only painting but contracting in general. After all this I realize how blessed my ignorance not taken advantage of by Greater Philadelphia area motivated young skilled pride-in-work honest hardworking + seasoned older employee of Scott Gribling Painting of Lansdale PA. I'm proud I had the idea that Tom Parkinson here taught me the phrase & affirmed paying daily "progress draws" & purchase receipts instead of advance deposit in case something happens to contractor, and as Tom teaches the natural effectiveness of receiving from the day's work :)

In England, little is known of the trade and its structures before the late 13th century, at which paint guilds began to form, amongst them the Painters Company and the Stainers Company. These two guilds eventually merged with the consent of the Lord Mayor of the City of London in 1502, forming the Worshipful Company of Painter-Stainers. The guild standardised the craft and acted as a protector of the trade secrets. In 1599, the guild asked Parliament for protection, which was eventually granted in a bill of 1606, which granted the trade protection from outside competition such as plasterers.[2]
My wife and I just painted the interior of our house with about 6-8 gallons, of $30+ per gallon (meaning the good stuff, non-diluted) with absolutely fantastic results. However we just paid an average of $5 per gallon. Reason...all big box stores have paint, set aside, that has been mixed but not picked up by the customer. They need to sell it quick and if you're not in a hurry (you know well in advance that a room or two need painting and it's not like the roof leaking and needs an immediate fix) you can go to each store when you need other supplies or food, like Walmart (when convenient, driving 20 miles to each is not worth it) and over the course of a month or two, pick out some very nice colors of quality paint. We found perfect colors...not saying they were our first choice but when we opened the can, very nice and some even better than our original picks. Cost to paint the entire house was about $100, with all materials included, period. We had it on the market for a few months to sell, didn't sell, painted the rooms, got 2 offers the day after we finished, took the best one and never looked back.
My son Owen and I thank you for the truly wonderful, informative and entertaining experience provided by the TOH staff, crew and trades-people at the Pro2Pro Brookline event. From Elizabeth - who welcomed us to the event, to Chris, Kevin and others who were wonderful during the orientation session (answering questions that I'm sure you have heard dozens of times before), to Charlie, Kevin, Richard, Heath (the electrician) and Thomas (the program director), you helped us Insiders to understand and appreciate the pride that you take in your work. It was refreshing. I loved the pictures and accompanying text of the event that you posted. I have to say in closing to Chris, Kevin and Thomas (in particular) you gave my son, a budding landscaper, the impetus to continue his pursuit of the trades. Kudos to you all and keep up your great work!
Before the scrubdown, protect nearby plants by misting their leaves and saturating the surrounding soil with water, pulling them away from the house, and shrouding them in fabric drop cloths. (Plants will cook under plastic.) Lay more drop cloths along the base of the walls to collect any falling paint debris. Walls should be wet down before getting scrubbed, then washed with a gallon of water mixed with 1 cup chlorine bleach and 1 cup of either a concentrated, phosphate-free cleaner, such as a trisodium phosphate (TSP) substitute, or Jomax House Cleaner. Working in sections, from the bottom to the top, will avoid streaks. Be sure to rinse walls well before the solution dries. Wood siding and trim should be ready to paint after a day or two of dry weather.
Not only careful communication is essential, but we would greatly recommend, when you pick out your type and brand of paint that you go and pay for it, with the contractor's discount, which is given by Sherwin-Williams and most paint companies. Then you will know how much paint you purchased and the coverage. If it is possible, inspect the work of the painter daily.
CertaPro Painters® provides a range of custom interior and exterior painting services, allowing for a smooth, seamless experience and exceptional results in every home. Whether you’re having your two-story foyer updated or refreshing the paint in your home’s bedrooms, the CertaPro Painters® team approaches every painting project with an eye for detail.
O'Neil patches shallow holes and divots with Ready Patch because it dries fast, sands smooth, and stays flexible. Deep cracks and rotten spots are best repaired with two-step epoxies, such as those made by Advanced Repair Technology. (For a step-by-step instructions, see Repairing Rot with Epoxy.) The days of using polyester auto-body fillers on wood are over. "They cure too hard," says Portland, Oregon–based painting contractor Kathleen George. "They look good at first, but then they peel away."
Spills and spatters happen, regardless of how careful you are. It’s a lot easier to pre- pare for them than to wipe them out of your carpeting or off your wood floor later. All it takes is canvas drop cloths in your work area (a 4-ft. x 15-ft. cloth costs $15). The thick canvas stays in place, so you don’t need to tape it, and you can use it to cover any surface. Plastic drop cloths are slippery to walk on or set a ladder on and don’t stay in place. Even worse, paint spills on plastic stay wet, and they can end up on your shoes and get tracked through the house. Canvas is slippery on hard floors, so rosin paper ($10 for 400 sq. ft. at home centers) is better over vinyl, tile and hard- wood. Tape the sheets together and to the floor to provide a nonslip surface.
Excellent advice because there are many unskilled workers who are "trying to pull the wool over the customers eyes". One has to study about the project for which they are in need. I happen to need dry wall repair and painting done in my home and feel the advice in this article will be a great help to me in hiring someone who is ethical and does good work. Thanks.
The best time of the year to paint your home is typically in late spring and early summer when it’s warm outside and moisture is low. This can change based on your geographic location. For example, fall can be a good time to paint in California when the difference between high and low temperatures is low. Your painter will select the optimal time to start your exterior painting project.
So sad that Angie's List requires the contractor be notified!! They have lost me as a client. If I'm dissatisfied and want to give an "F" rating (question/workers...I SHOULD NOT be intimidated into passing up an opportunity to explain my experience! There is NO WAY my contractor got an Aplus rating from over five hundred people....so someone was lying....yet I can't report that without the contractor knowing it? REALLY?
I am getting quotes to paint the exterior of a 2,500 sq ft split levei home that just had all new windows and pre-primed Hardiplank installed 3 months ago. the quotes are up to $2,500 different ranging from power wash,prime again 3 coats of paint to no powerwash needed so soon and one coat of paint.. All quotes include trim. One includes complete replacement of 80 feet facia boards another just 40 feet.

When determining the total cost of a home exterior paint project, you'll want to include the cost of materials like paint, supplies and other items you might want to cover in addition to the siding. If you know the average cost of these items in addition to your home exterior project cost, you'll have a good plan in place when you start calling for professional estimates. This also gives you the option to purchase or paint some items yourself to save money. Here are some of those cost factors and what you might expect to pay:
To get basic measurements, measure the length and width of each wall you want to paint in inches. Multiply the length and height together, and divide by 144. This will give you the square footage for each wall. A gallon of paint typically covers around 400 square feet. In some cases, you may need a primer 2 first, then a single coat of paint, meaning that you may need one gallon of primer and one gallon of paint to cover 400 square feet. However, if the wall requires multiple coats, this will increase the total amount of square footage required, and therefore the amount of paint.
Over time, even the best paint job needs a new coat. Old paint peels and fades and those colors that were all the rage ten years ago can start to look a bit dated. With your busy schedule, you've got no time to pick up a paintbrush, and you've just remembered that your in-laws are in town for dinner next week! We hear stories like this all the time, and our reply is always the same: don't panic! Book a painting professional through the Handy platform. Wall painting shouldn’t be stressful and when you use the Handy platform, it won’t be.

PSA: Color psychology is a thing. The right soothing hue can work wonders for your mind and soul. You might think that only works for pale blues, but the contrast of a light and dark color — or, in this case, off-white walls with chocolate brown and deep blue accents — has a powerful effect. "The darker color grounds the room, and then the lighter runs right up to the ceiling and makes it feel higher. It creates this serene atmosphere," designer Laura Bohn told us.


This article with comments was terrific - it was so informative. I found the advice useful. It addressed specifics like the condition of the dry wall surfaces, any additional repairs such. pin holes, chalking, smoothing of wall surfaces, absorption of paint and number of coats that may be needed. It should also include insurance coverage, and reflect the clean-up afterwards. Having a written contract with the company's letterhead is a must.
Some proposals simply say to paint the walls and ceiling and never specify the number of coats to be applied. If the colors are similar enough, it's possible to get away with one coat of paint and not discount your pricing. No matter how hard you try, tiny, pin-sized air holes will pop exposing the original walls. This may not bother you if you can't notice it, but principally speaking you should have paid your painter less for the work.
Safest way to ensure that everything is fair is to get it ALL in writing , signed by both parties. Specify each item that needs repair. Also, BUY the paint YOURSELF. That way, there is no incentive to water it down, and you KNOW that you are getting the grade/quality you actually purchased. Don't be penny wise and pound foolish; if you are paying to hire a painter, buy the best paint that you can afford, to ensure maximum life of this home improvement.
A thorough scrubbing is a must before painting any exterior surface. It removes the dirt and broken-down paint residues that keep fresh coats from adhering and gets rid of mildew that grows on paint in all but the most arid climates. Most contractors clean with pressure washers, but in the hands of someone unfamiliar with the equipment, these can gouge wood, shatter glass, and drive water behind siding and trim. Using a hose, a pump sprayer, and a scrub brush is slower but safer, and just as effective.
Dave, you said it best! Every pro painting contractor truly worth their salt would and should cut and paste exactly what you say here about where customary and legitimate practices and expectations should be in regards to what customers should expect from contractors and how contractors should professionally deal with their customers. By the way, Dave, if you work in the Atlanta area, I would like to hire you! Thank you for your valuable advice!
Repaint — exteriors especially — before visible signs of wear appear, Bancroft says. Don’t wait until you see peeling or flaking paint. “If I have to spend 40 hours preparing the surface before we can paint, that time is going to result in a lot of extra costs. But if I can spend 10 hours preparing the surfaces to be painted, you’re going to save money,” Freeman says.
Inspect the surface area for holes, cracks or other problems and apply acrylic caulk to fill them in. Use a putty knife to smooth out the caulk and remove any excess to prevent bumps. For particularly thin or narrow crevices, you may have to use your finger to smooth out the caulk. Caulk contracts and shrinks, so apply a second layer once it's dried.

I'm an architect and my firm routinely specifies interior finishes for projects so I thought I'd contribute a professional's perspective on the issue of how many coats of paint are deemed "acceptable". The fact of the matter is the average consumer usually isn't a paint expert and can't be expected to know about all the factors that impact coverage. That knowledge is considered "means and methods" and in a court of law, the responsibility lies with the painter or general contractor, not the consumer. What the consumer should be concerned about is the final result-does it look good and is it what you expected? The simplest way to communicate this to your painter is to stipule in your written agreement that the number of coats will be "as required to cover". That way all the guess work about what kind of primer, how many coats, how color affects the scope of work, etc., is removed from the consumer's responsibility and resides where it belongs-with the professional. In the contract that's why retention is always a good idea-typically 10% is withheld from payment until the job is completed to the satisfaction of the customer. Of course in return you as the customer have to be reasonable about what constitutes a completed job. Just my $.02.

Home Painter Co

×