The only time it's acceptable to mix water in the paint is when you're using a deep or ultra deep base paint to reduce its stickiness, which is rare with new paint technology. Dark primary colors are composed almost entirely of tint that makes it very hard to work with without adding water. (You never use a sprayer and need to thin paint.?) If i was still in the industry I'd take the time to make a better article than this. Take this for a grain of slat. Use a reputable painter or someone you know you can trust or has been referred to you by someone you trust. I wouldn't hire anyone I had to watch like a hawk to make sure they're not screwing me.
The article and comments were great information to have before deciding how to go about getting a painting job done. I think the important point is that there are several key choices (who to do the work; color, sheen, quality, of paint; how many coats; amount of prep/repairs to be done and by whom, how long the job will take, provisions for changes, how detailed the contract needs to be; advanced deposit/progress payments/final payment; final inspection, etc.) that need to be made and it requires advanced research and planning in order to become well enough informed to make the right choices. Then it requires spending sufficient time to check materials and inspect the quality of the work while it is on-going, raher than waiting to do it all at the end. President Reagan's philosophy of "Trust, but verify." applies.
Generally speaking, based on either personal experience or simply what you have heard, do painters have an outstanding reputation? Rightfully so – answering honestly and without elaborating, most homeowners, builders and property managers would likely say no. As a consumer that is familiar with some painter’s reputation – if you overlooked the importance of conducting extensive research by not asking qualifying questions and getting the proof – what would you say your chances are of having a bad experience? Obviously, pretty likely! Right?
Concrete walls must always be prepared before painting, but in some cases previous finishes will also have to be removed so that paint doesn't peel or chip off. Additionally, special sealants, primers and paints may be applied to ensure concrete's endurance in face of the specific elements. Depending on the wall's condition and exposure to the sun, painting professionals will usually estimate between $500 (~250 sq. ft.) and $2,000 (~1,000 sq. ft.), depending on wall area to cover.
In 1894, a national association formed, recreating itself in 1918 as the National Federation of Master Painters and Decorators of England and Wales, then changing its name once again to the British Decorators Association before merging, in 2002, with the Painting & Decorating Federation to form the Painting & Decorating Association. The Construction Industry Joint Council, a body formed of both unions and business organizations, today has responsibility for the setting of pay levels.[2]
I would not recommend this company for the following reasons:1. Original appointment was very specific to them on what was needed and to take photos for 3 apartment unit plumbing fixture repairs. One unit had a bathroom tub/shower backup.2. No photos taken, 3 trips later and only 1 unit completed to satisfaction. (Backup) 3. Other faucets unable to find on line with their suppliers and repair 4. Had to find another plumbing company to complete the jobs. 5. Invoicing had to be redone as not in detail of job address for tax purposes 6. Bad communication throughout the project process with their internal customer service. Their technician and project manager ordering parts. 7. For the back up. Did not bring out correct snake on both trips and had to replace lines as too small to break through backup. Costing over $800 for 3 trips just to complete that situation out. 8. Ordered the wrong parts when 2nd trip out since no photos taken to confirm what was needed. Very dissatisfied and will never ask them to work in any of our rental properties again.
You've got me very afraid now, I've been taken in a couple of times since I moved here. They take advantage of me because I am a single woman, not exaggerating! From gardeners to inside work. Wouldn't have house painted but I know my HOA will be after me soon, garage door is peeling and stucco needs repair. Got the $1500.00 deal, but paying more for extra work they say I need.
The companies with the best paint products are Benjamin Moore, Dunn Edwards, Sherwin Williams, and Vista Paint. As a painter I don't recommend Berh from Home Depot as much because it's quality is just marketing. Flat paint has no sheen and it shows its true color, but is not easy to wash or clean. Satin, eggshell have low sheen and is washable. Semigloss ang glossy has a high sheen and these paints are recommended for bathrooms and kitchen or where there's high humidity and steam.

Most painters have no problem painting doors in place, but they recommend you lay the door on sawhorses and work horizontally. If you have a paneled door, start with the panels and work from the outside edges in toward the center. "Watch the corners — paint loves to puddle," warns Dixon. While the paint is still wet, lightly "tip off" the panel with an almost dry brush. (Tipping off is pulling the brush over the surface to level out the finish.) When painting the stiles (vertical) and rails (horizontal) just follow the grain of the wood. When the grain changes abruptly, for instance, where the rail meets the stile, don't stop your brush stroke — you'll only leave a lump of paint. Apply paint across the joint with a full stroke, and then tip off the overlapping section by pulling the brush in the direction of the grain. "Make sure the door is dry before painting the opposite side or rehanging it," says Maceyunas.
If you hire a contractor for a painting job, you’ll want some assurances in the form of guarantees or warranties.  Knowing the importance of warranties, some companies even give unrealistically long warranties such as 10 years, 20 years or even lifetime warranties. The sad fact is that most of these companies will be out of business long before their warranties expire. So what is a realistic warranty that you can trust? Here’s what you should look for in a great warranty:
There’s a new classical station in town, and I listen even though the reception doesn’t seem to be as strong. In our absence, I hope you will avail yourself of other fine magazines and resources to keep up, maybe you’ll see me back in the industry sooner or later. Going out of business due to advances in digital technology isn’t new—I was just reading about the Pony Express succumbing to the much cheaper and faster telegraph in 1861. 

To paint a large section without leaving lap marks, roll the nearly dry roller in different directions along the dry edge, feathering out the paint as you go. After completing the entire length of the wall or ceiling, move to the next section and paint over the feathered edges. For the second coat, apply the paint in the opposite direction. This crisscrossing paint application sharply reduces (if not eliminates) lap marks.


Every home has details that can be accentuated for amazing looking visual appeal and first impressions.  The key is to not make the wrong details stand out.  Entryways, windows, shutters and other details on the home can be painted to make their design noticeable.  However features such as gutters, downspouts, external air conditioning systems, unevenly proportioned windows and protruding garage doors should not be completed to draw attention to them as this will provide a negative results.
The best time to tackle windows is in the beginning of the day, when you're fresh," says Doherty. "But it still takes me an hour to do a standard window." For double-hungs, begin by raising the inner sash and lowering the outer sash until their positions are almost reversed. Paint the lower half of the outer sash first, then the entire inner sash. Once the lower sash is dry, return both to their normal position, but leave them slightly open. Finish painting the outer sash. "Windows take too long to tape," says Doherty. When painting, overlap the glass by 1/16 inch to seal the wood.
Homeowners with wood siding have the option of staining or painting siding that has been worn down by the elements -- especially if they need to increase its defenses against the sun or extreme humidity. Holes, missing pieces or other problems will increase the overall cost of the painting project. You can expect to pay between $700 (~250 sq. ft.) and $2,000 (~1,000 sq. ft.) to paint wood siding, but this project will also help to protect the home's exterior from more extensive repairs down the road.
I disagree with your criteria to hire a painter. A prompt returned call is nice but does not indicate the quality or fairness of the painter. As far as a written estimate, that should be more of a qualifier for the bid versus an evaluation criterion. I'm not sure one would have favorable results by hiring a painter on this basis. As far as the bidding process, change orders should ONLY be used if the customer requests additional scope (PMP 101). Angie's list should consider asking reviewers if/how much they were told to pay compared with the estimate. Unfortunately, there are a lot of contractors that are unethical and need to be accountable.

Because of our wet/cold weather, another painter was booked out through August as of May 7th, 2016.  Anyone even thinking about a VA loan refi should get estimates for painting and pest inspections BEFORE starting on the loan paperwork, otherwise you will have difficulty getting painting and inspections done in a timely manner (and it is my understanding this is common with VA loans.)  
Keep an eye on the new cans as they're being brought in. Make sure they look new and don't have paint in the rim of the can. If it's a five-gallon bucket, check to see whether the lid is still sealed on with the plastic strip. The only time it's acceptable to mix water in the paint is when you're using a deep or ultra deep base paint to reduce its stickiness, which is rare with new paint technology. Dark primary colors are composed almost entirely of tint that makes it very hard to work with without adding water.
Ideally, you want as much paint on the brush as you can control without making drips or blobs. To do this, Doherty dips his brush about 1 1/2 inches into the paint, then taps (not wipes) each side of the brush against the side of the can. Tapping knocks off the drips and forces the paint into the bristles. "The brush releases the paint just like a fountain pen," he says. Weeks agrees, saying, "Just be sure to keep your brush moving, or it'll start to drip." For more delicate work, such as when you're painting trim or window sash, you'll want less paint on the brush. Doherty again dips and taps his brush, but this time he also scrapes the sides against his can. "The outside bristles are drier and easier to manage," he says, "but there's still plenty of paint on the brush."
I am a painting contractor and have been since 2001. Make sure the estimate provides in writing: What is EXCLUDED as well as INCLUDED. It should state the manufacturer and type of paint going to be used. Estimate says ALL LABOR AND MATERIALS. My estimates to my customers say "guaranteed coverage" eliminates the conversations of 1 coat vs 2 coat. I have my customers submit colors 5 days prior to start date. Customers need to inform me if they are going to use pure white, dark reds, oranges, and bright yellows they need to inform me in that 5 day window, so I can adjust my pricing for 3 coats. Although this more uncommon now than years past because a lot of paint manufacturers have primer with paint products. Let the contractor know if your doing accent walls. This takes longer to cut in straight lines and it requires the contractor to purchase more paint. If you add anything on the scope of work have the painter write out the description and cost prior to them doing the work. Have the estimate say how many days it will take to perform the work. Ask how many workers will be doing the job. Make sure to enforce that number of workers their everyday until the job is complete. Do not give final payment until you do a final walk through. Walk the job when its almost complete and point out areas that you want fixed prior to the contractors final walk through. Its best to do while the workers are still in that particular area as they will have tarps down and areas covered and it will be easier for them to take care of. Purchase a roll of blue tape and stick it to areas that you want fixed. This is called a punch list.

The article was well-intended, but it makes it sound like painters are the crooks and consumers are innocent victims. That is blatantly un-true. Maybe there should be a follow-up article that educates consumers how not to be shysters by expecting a ton more than they said at the start, or not paying the balance of the job unless something else is done that was not in the contract. Tradesmen have a rough road when dealing with consumers that have short arms but long lists of by-the-way items. No, I'm not a painter...
Disclaimer: NerdWallet strives to keep its information accurate and up to date. This information may be different than what you see when you visit a financial institution, service provider or specific product’s site. All financial products, shopping products and services are presented without warranty. When evaluating offers, please review the financial institution’s Terms and Conditions. Pre-qualified offers are not binding. If you find discrepancies with your credit score or information from your credit report, please contact TransUnion® directly.
At Five Star Painting, we offer free price estimates, so there’s no reason to hesitate! Our house painting contractors know what they’re doing, and they do it well! Call our residential painting experts today at (888) 261-3633 to receive your free estimate or to schedule a home visit. Use our online scheduler to pick the date and time of your consultation.
If less than half the old paint is left, however, it may be worth stripping it all off. Guertin gets rid of stubborn remnants using shrouded grinders (like the PaintShaver), infrared paint strippers (such as the Speedheater), or chemical strippers (like Multi-Strip), then smooths the wood with a course or two of sanding. When siding (or bank accounts) can't take the shock of a total strip job, Rich O'Neil, of Masterwork Painting in Bedford, Massachusetts, has successfully hidden rough, well-adhered paint under Peel Bond, a thick primer.
Removing and installing wallpaper can be a tricky task. The crew at CertaPro Painters® is skilled in removing wallpaper and will make this time-consuming task, hassle-free for you. We will work with you to help you choose a wallcoverings style that’s perfect for your home, and then apply it to your walls. All you’ll have to do is enjoy the final look.
At Five Star Painting, we offer free price estimates, so there’s no reason to hesitate! Our house painting contractors know what they’re doing, and they do it well! Call our residential painting experts today at (888) 261-3633 to receive your free estimate or to schedule a home visit. Use our online scheduler to pick the date and time of your consultation.
Oh, where to begin? Let me start with 'watered down paint'. 25-50% before the material gets to the site? Impossible. You would basically be painting with water at that point. It would be less of a hassle, and cost, to simply use proper material. You would be forced to apply three coats instead of two, as the coverage would be horrible. Whatever cost you think might be saved in materials would be lost in labor.
More recently, professional painters are responsible for all preparation prior to painting. All scraping, sanding, wallpaper removal, caulking, drywall or wood repair, patching, stain removal, filling nail holes or any defects with plaster or putty, cleaning, taping, preparation and priming are considered to be done by the professional contracted painter.
This all comes down to the rules.....1. references....does the contractor have them??? I ALWAYS furnish all my prospective customers them....no excuses...2. insurance....again, I always furnish proof....3. Read the proposal carefully...I ALWAYS list materials down to tape used, the brand, the grit of sandpaper, the manufacturer, etc....its INEXCUSABLE to not list all of these items....I am a member of the PDCA, the Painting and Decorating Contractors of America, the foremost authority in the coatings industry and they also approve of what I listed....if you do not follow these guidelines, you will NOT get a job reflective of "professional". Look for the PDCA where any painting contractors are, if they are not a member, RUN!

If your home was built before 1978, there is a good chance that lead paint was used in its construction. Scraping, sanding, or removing old paint can release toxic lead dust which can cause serious illness in children and pregnant women. Special handling is required when working with lead-based paints. If lead paint is present in your home, you will need to hire a lead-certified painting contractor or lead abatement contractor. Before getting started with your exterior painting project, consult your local building authority or visit www.epa.gov for more information.
I do not mean to come off with an edge, however, this is an article for people hiring low bid, uninsured, one man band painters out to "hustle" a buck. Hire reputable, established companies or hire someone you know or have a strong referral from. If you are arguing over watered down paint, ticky, tacky deposits, buying your own supplies, you have hired the wrong guy.
Climate is another factor to consider. Sunlight, wind, rain and salty weather can all wear out exterior paint. Oil-based paint is durable against wind, rain and temperature changes, but sunlight tends to degrade it. Alkyd paint chalks and sheds very thin layers when it begins to wear. Latex paint is the more durable option for very sun-drenched and relatively dry climate areas. Latex paint with high vinyl content should be avoided, however. Acrylic resin is by far the more durable binder for outdoor latex paint.
The perfect roller would hold a roomful of paint, leave the right amount of texture, wouldn't spray or fuzz, and would be easy to clean. Until somebody invents the ideal one, follow these tips to choose the right roller. "The longer the nap, the more paint the roller will hold, but it will also create more texture." says Dixon. "A 1/2-inch nap lamb's-wool roller holds plenty of paint without too much texture," says Dixon. "Less expensive rollers can work," says Span. "Just wash them first in dishwashing liquid to remove any stray fibers." Most of the pros we spoke with prefer 9-inch rollers over 18-inch models -- they are lighter, cheaper, and easier to use. Despite these shortcomings, Maceyunas swears by the wider roller. "The roller can do a whole wall in a few up and down strokes instead of in several dozen W and M strokes," he says.
Freshly painted walls often look blotchy. The color is uniform, but the sheen isn’t consistent. This usually occurs over the holes and cracks you patched with a filler or drywall compound. The porous fillers absorb the paint, dulling the surface (a problem called “flashing”). When light hits these dull spots, they stick out like a sore thumb. The smooth patch also stands out in contrast to the slightly bumpy texture of the rest of the wall. A quick coat of primer is all it takes to eliminate flashing and texture differences.
×