When hiring a contractor it is always best to hire one who is personally referred to you by someone you trust. Hiring through ads or phone book is hit and miss. Check with your local paints stores, they know the good guys from the bottom feeders. Go to the stores that sell the high quality paints like Benjamin Moore(nonpareil), Pittsburg, Sherwin Williams or Glidden. Don't go the the big box stores for referrals, the people there don't know squat!
I'm hiring an interior painter and that is why I was reading this comment list. I'm concerned about your comment about Angie's List. Some of us don't have personal recommendations for tradespersons, and rely on sites like this. Are you saying that Angie's List's reviews are not complete or that they do not print some of the negative reviews? It's hard to know what to do - I have not been able to find a person who just had their paint done so I can ask him/her about the quality of the painter.
Specify whether the contractor or you will supply the paint. Check Consumer Reports' paint ratings: In its tests, some relatively inexpensive paints performed better than more expensive paints and cost $10 to $20 less per gallon. But keep in mind that most paints will resist cracking, peeling, mold and mildew. Who does the painting — and how well they do it — is more important than what's in the bucket.
A fresh paint job has the power to totally transform the look of your house in less time and for less cash than any other remodeling project. That thin skin of resin and pigment also protects your investment, shielding it from sun, wind, and rain—until the paint begins to crack and peel, that is. Then it's time to button up with a couple of new coats. Properly applied, new paint should last for a good 15 years, provided you use top-quality materials, apply them with care (and with an eye on the weather), and, most important, clean and sand every surface first. Here's what you need to know to get a first-class finish on your home's exterior.

The pros were split on this tip. "Masking tape is problematic," says Mark Dixon, a painter in Missoula, Montana, and author of "House Painting Inside and Out" (Taunton Press, 1997). "Paint can bleed behind the tape, or remove the paint it's stuck to." Another problem is bridging. "Latex paints form a skin," says Dixon. "Removing painted tape can tear the skin, resulting in a ragged rather than a sharp line." Lastly, taping takes time. "Learning how to cut in with a brush takes practice, but if you can do it, you'll leave most tapers in the dust," Dixon says. (Cutting in is painting just the surface you want, not the surface adjacent to it — for example, where a wall meets the ceiling.) On the other hand, "If you can't cut in, you can't beat tape," says Span. The pros we spoke with all recommend painter's (blue) tape because it's easier to remove than masking tape. To prevent bleeding, Span uses a putty knife to bed the tape. After letting the paint dry, he scores the edge of the tape line with a utility knife to avoid tearing the paint.

OF the different type of customers there are at least two: cheap charley's and people who want great results. I agree the need for wall repair is critical to the end results. Most critical is for the customer to be told ahead that the walls are going to need exactly what is needed. This means the contractor must look, touch, examine the walls for defects and needed work. I've been a building manager for 40 years and seen a few paint jobs. Typically a contractor does a lot of talking about how expert he is, but the guys who walk through with note pads, iPads, examine, measure, point things out, explain and recommend are the ones I will deal with. It confirms if they know what the business. Nobody likes the workers to show up and when you talk about the job they're going to do they know nothing but they we were told to be here. Their boss who bid the job doesn't supervise - a big no no around here. Nobody likes surprises or worse, at the end of a job that's not right getting a bunch of little kid excuses. Contractors that do not like the customer to be around looking at the progress don't get the job.


Some proposals simply say to paint the walls and ceiling and never specify the number of coats to be applied. If the colors are similar enough, it's possible to get away with one coat of paint and not discount your pricing. No matter how hard you try, tiny, pin-sized air holes will pop exposing the original walls. This may not bother you if you can't notice it, but principally speaking you should have paid your painter less for the work.
In 1894, a national association formed, recreating itself in 1918 as the National Federation of Master Painters and Decorators of England and Wales, then changing its name once again to the British Decorators Association before merging, in 2002, with the Painting & Decorating Federation to form the Painting & Decorating Association. The Construction Industry Joint Council, a body formed of both unions and business organizations, today has responsibility for the setting of pay levels.[2]
On its last day, I was listening to see how they would handle it. They brought in personalities who were friends of the station for interviews, played some popular pieces, and were set to sign off at the appointed and anointed 10 p.m. They put on a recording of Beethoven’s 9th, which for many people still holds its place as the finest piece of Western music ever composed. But what would they say afterwards? I waited to hear, and they said the classiest thing they could: nothing.
I turn away any job when the client refuses to pay anything up front. It sends a red flag. I also charge a scheduling fee which is non-refundable. I get 33 percent when I show up and begin work. Another percentage halfway through, and the balance upon completion after client is satisfied. There needs to be skin in the game for both parties as a measure of good faith. If you are dealing with a reputable company (did your due diligence, right?) why wouldn't you want to pay something as work progresses? We do this not only because we love to paint but we require cash flow to stay in business. There is not always 'money in the bank' as you suggest. It's tough these days. The suggestion buy 'Kim' 'Never pay a contractor a deposit' is nonsensical.

Unless you like textured walls, don't paint over dust. Wash the walls with trisodium phosphate (TSP) or a mild cleaner, like Jasco's TSP No-Rinse Substitute. For smoke-stained walls, Toto uses a 50/50 solution of bleach and water. To clean a wall, use two buckets. Load up your rag or sponge from your cleaning-solution bucket, and scrub. Before redipping, rinse the sponge in a second bucket filled with clean water.

To maintain a wet edge, start near a corner and run the roller up and down the full height of the wall, moving over slightly with each stroke. Move backward where necessary to even out thick spots or runs. Don’t let the roller become nearly dry; reload it often so that it’s always at least half loaded. Keep the open side of the roller frame facing the area that’s already painted. That puts less pressure on the open side of the roller, so you’re less likely to leave paint ridges when doing DIY wall painting.


I am getting quotes to paint the exterior of a 2,500 sq ft split levei home that just had all new windows and pre-primed Hardiplank installed 3 months ago. the quotes are up to $2,500 different ranging from power wash,prime again 3 coats of paint to no powerwash needed so soon and one coat of paint.. All quotes include trim. One includes complete replacement of 80 feet facia boards another just 40 feet.
If you paint over dirty, oily surfaces, the paint will easily chip or peel off. So before painting, clean grimy areas with a deglosser or heavy-duty cleaner intended for prepaint cleaning. They work well to clean painted, varnished or enameled surfaces to improve the adhesion of the new paint. They’re ideal for cleaning greasy or oily areas like kitchen and bathroom walls and removing hand marks around light switches and doorknobs.
O'Neil patches shallow holes and divots with Ready Patch because it dries fast, sands smooth, and stays flexible. Deep cracks and rotten spots are best repaired with two-step epoxies, such as those made by Advanced Repair Technology. (For a step-by-step instructions, see Repairing Rot with Epoxy.) The days of using polyester auto-body fillers on wood are over. "They cure too hard," says Portland, Oregon–based painting contractor Kathleen George. "They look good at first, but then they peel away."
YP - The Real Yellow PagesSM - helps you find the right local businesses to meet your specific needs. Search results are sorted by a combination of factors to give you a set of choices in response to your search criteria. These factors are similar to those you might use to determine which business to select from a local Yellow Pages directory, including proximity to where you are searching, expertise in the specific services or products you need, and comprehensive business information to help evaluate a business's suitability for you. “Preferred” listings, or those with featured website buttons, indicate YP advertisers who directly provide information about their businesses to help consumers make more informed buying decisions. YP advertisers receive higher placement in the default ordering of search results and may appear in sponsored listings on the top, side, or bottom of the search results page.
Stucco is a specialized material that requires extensive preparation work (cleaning, caulking, filling in cracks, etc.). Additionally, paint suitable for rolling or brushing over stucco varies greatly depending on location and climate conditions. Some stucco paint varieties will chip and peel away in certain climate conditions, so painting professionals won't recommend them. These factors make stucco one of the more expensive siding materials to cover. You can expect to pay anywhere from $900 (~500 sq. ft.) to $3,000 (~1,500 sq. ft.) to have stucco revitalized with paint, depending on how much is needed to cover the home exterior.
Hmmm...Intro to E12...looks suspiciously like a freehand angled cut on that contractor saw... Yes, the riving knife might save you from a dangerous kickback...but still a very bad idea.. Why not a 'safety segment' explaining kickback and why you should not do this (styrofoam demo, back side of the blade teeth rising up grabbing the foam and throwing it back at you...)
The other difficult part is getting a painting contractor to show up. While this generalization does not apply to every painter, personally I am extremely grateful if I can get a paint contractor to show up to look at the house and to later produce a written estimate. I hardly fault the painting contractors, because I think it is a combination of the contractors being smaller operations along with a high demand for their work.
Buying a can of premium paint, then bait and switch over to low-line products? Again, complete nonsense. Think about it for a moment; the Painter needs 5 gallons of wall finish. So, he buys one can of premium and the rest 'cheap'? How is he going to hide the 4 other gallons? What's he going to hide it in??? He only has ONE gallon of premium. It's not as though he's going to keep older can labels, they would be covered in paint of a different colour.
Generally speaking, based on either personal experience or simply what you have heard, do painters have an outstanding reputation? Rightfully so – answering honestly and without elaborating, most homeowners, builders and property managers would likely say no. As a consumer that is familiar with some painter’s reputation – if you overlooked the importance of conducting extensive research by not asking qualifying questions and getting the proof – what would you say your chances are of having a bad experience? Obviously, pretty likely! Right?
After our own inspection, your Job Site Supervisor will walk you through the space, giving you the opportunity to review our work and to provide any initial feedback. You may also be contacted for a follow-up satisfaction survey so that we know how we measured up to your expectations. Our paint jobs are designed to last up to 7 years on a properly maintained surface, so you will get to enjoy your beautiful newly painted room for years to come.
These are some fantastic questions to ask and I particularly like the one that is concerned about safety for the painters. After all, if you have a large home and you’re hiring them to paint the exterior of that home then they’ll likely be on scaffolding. Because of that, you need to make sure that the contractor not only provides appropriate safety training, but has the correct liability insurance as well.
Are you looking for interior house painters that are local, reliable and the best at what they do? Does the idea of painting the walls of your home fill you with dread? If you want to get the best results with minimal fuss, then make Handy your first choice when you need to connect with expert painting contractors. From preparing your interior walls and ceilings to achieving a neat, professional finish, Handy will put you in touch with the right people for the job. Customize your request by specifying your job details, from how many painters you need to how long you’ll need them. We’ll connect you with the painting professionals that suit you best with no compromise on quality.

I totally agree with this as well. I think every time I have read Angie's List reports, they are inaccurate and not researched enough. I had COMPLETE faith in Angie but lately I am hesitate on reports. I would check your local hardware store or even your neighbors to get a recommendation for painters. If you liked what you saw, you can be stress free with your results. I live in Texas and I have borrowed my hardware store opinion bc that seems to be the place most of the contractors or painters come to buy stuff for the jobs. If your neighbors painters, contractors, electricians and plumbers have shown good results, stress free you. I have been stress free with results, glad I asked for other opinions.Don't forget, the Hardware Store knows if that person is trustworthy and honest, their accounts would be shut down.


Not only careful communication is essential, but we would greatly recommend, when you pick out your type and brand of paint that you go and pay for it, with the contractor's discount, which is given by Sherwin-Williams and most paint companies. Then you will know how much paint you purchased and the coverage. If it is possible, inspect the work of the painter daily.
The cost to paint metal siding -- most commonly aluminum and galvanized steel -- will depend on a variety of factors. In some instances, a simple cleaning will suffice to prepare metal siding for painting. In worst cases, painting professionals will need to repair metal that is rusted, damaged or missing pieces due to climate conditions. In the case of severe damage, a professional will have to remove the old finish and paint to get to the original layer, which will add on to the final price. When you add the actual painting of the metal siding, you might be looking at a final bill between $400 (~250 sq. ft.) and $1,500 (~1,000 sq. ft.).

• One room or the whole house? Applying one coat in one room is a reasonable DIY Saturday project (especially if you have help and beer). Multiply the time spent moving furniture, prepping walls and sanding old trim by the number of rooms in the house, and you might want to hire real help. It's the same outside. You can probably tackle one shady garage wall that needs a little scraping and sanding plus a coat of paint, but covering all surfaces of the house is usually best left to a pro.
When you refinish your existing cabinet doors, you get a whole new look without the astronomical costs normally associated with a kitchen remodel. It’s a much smarter way to update your space, especially if your cabinets are still in good condition. It doesn’t make sense to throw out perfectly good materials, just because you’re tired of the color.
WOW! I think the guy I hired read this first and I have photos that would make your skin crawl. Bottom line: he got me for $1900.00. Every single thing he painted had to be completely redone....that's when I discovered he did NOT use the colors I picked, he actually used leftover exterior paint from his mother's house! Because I have pets he said things needed to be sealed first and I did agree to that. What I did NOT agree to was using some kind of foul smelling gray stuff ON MY HARDWOOD FLOORS! THEN he painted them BLACK, telling me that all they were good for was covering over with laminate or carpet. He also dripped and tracked paint all over my ceramic tile floors. PLUS left a wet used paint roller in my garden window and had stuff piled in front so I didn't find it until it had dried. I have no idea how much that is going to cost to repair. Then he left without finishing (thank God) but left the "leftover" paint, uncovered, in the rain. Again, hid it so I didn't immediately find it. Obviously we will be going to court but I doubt if I see a penny from him.

Home and business owners alike know that the professionals of Southern Painting are the best painters in Fort Worth to trust. Not only are our painters bonded and insured – we also back our work with a transferrable Three-Year Limited Labor Warranty. Combine that with over 28 years of experience, and there’s simply no reason to go anywhere else. We provide services above and beyond what you can do yourself, and we go further for our customers than any of the other painters Fort Worth has to offer.


Most of us can do an okay job of painting a room. But a seasoned professional does a great job. Obviously, pros have more experience than the average homeowner, but they also know techniques and tricks that make them better painters. We asked six pro painters to share those secrets. They probably kept a few tips to themselves, but they provided us with more than enough to help you work more efficiently and get better results. Some of what you'll read may surprise you. For instance, their secrets won't cut painting time. Painters spend two to four days on an average-size room. That's how long it takes to prep, prime and paint correctly. It's more work, but when you stand back to admire the results, you'll agree it's time well spent.
If you paint over dirty, oily surfaces, the paint will easily chip or peel off. So before painting, clean grimy areas with a deglosser or heavy-duty cleaner intended for prepaint cleaning. They work well to clean painted, varnished or enameled surfaces to improve the adhesion of the new paint. They’re ideal for cleaning greasy or oily areas like kitchen and bathroom walls and removing hand marks around light switches and doorknobs.
Residential house painters on the Handy platform have used countless gallons of paint and tons of brushes over the years. With a wealth of experience under their belts, they know the best, quickest and most cost-effective ways to get the work done. From how to achieve that perfect glossy finish to ensuring no paint drips onto your crown molding, you might find yourself picking up a few tips!
The perfect roller would hold a roomful of paint, leave the right amount of texture, wouldn't spray or fuzz, and would be easy to clean. Until somebody invents the ideal one, follow these tips to choose the right roller. "The longer the nap, the more paint the roller will hold, but it will also create more texture." says Dixon. "A 1/2-inch nap lamb's-wool roller holds plenty of paint without too much texture," says Dixon. "Less expensive rollers can work," says Span. "Just wash them first in dishwashing liquid to remove any stray fibers." Most of the pros we spoke with prefer 9-inch rollers over 18-inch models -- they are lighter, cheaper, and easier to use. Despite these shortcomings, Maceyunas swears by the wider roller. "The roller can do a whole wall in a few up and down strokes instead of in several dozen W and M strokes," he says.
So sad that Angie's List requires the contractor be notified!! They have lost me as a client. If I'm dissatisfied and want to give an "F" rating (question/workers...I SHOULD NOT be intimidated into passing up an opportunity to explain my experience! There is NO WAY my contractor got an Aplus rating from over five hundred people....so someone was lying....yet I can't report that without the contractor knowing it? REALLY?
The BBB isn't a painter-specific group but rather an organization that is dedicated to ensuring that consumers can access information about anyone they do business with. The BBB also rates companies based on a Standards of Trust scale, which goes from A+ to F. A company doesn't have to be a member to get a grade, and it's a good idea to check to see how your contractor is scored as well as its membership status.
The pros were split on this tip. "Masking tape is problematic," says Mark Dixon, a painter in Missoula, Montana, and author of "House Painting Inside and Out" (Taunton Press, 1997). "Paint can bleed behind the tape, or remove the paint it's stuck to." Another problem is bridging. "Latex paints form a skin," says Dixon. "Removing painted tape can tear the skin, resulting in a ragged rather than a sharp line." Lastly, taping takes time. "Learning how to cut in with a brush takes practice, but if you can do it, you'll leave most tapers in the dust," Dixon says. (Cutting in is painting just the surface you want, not the surface adjacent to it — for example, where a wall meets the ceiling.) On the other hand, "If you can't cut in, you can't beat tape," says Span. The pros we spoke with all recommend painter's (blue) tape because it's easier to remove than masking tape. To prevent bleeding, Span uses a putty knife to bed the tape. After letting the paint dry, he scores the edge of the tape line with a utility knife to avoid tearing the paint.
Pros prefer 5-gallon buckets with a roller grid to roller pans. They hold more paint than pans and, says Doherty, "It's tougher to tip over a bucket." A bucket also lets you box, or mix, two or three cans of paint to avoid color discrepancies. To use a bucket and grid, dip the roller a quarter of the way into the paint and run it over the ramp to work the paint into the nap.
If there is any peeling — and there usually is somewhere — it's essential to scrape off any loose paint. This doesn't just mean the parts that are already separated from the wood and ready to fall off on their own. Each spot where paint has peeled loose needs to be scraped thoroughly until you can no longer get the sharp corner of a putty knife under any of the surrounding edges of paint. Then, the bare spot needs to be sanded until the paint edges are smooth.
When coverage is difficult to estimate, add more rather than less when doing DIY wall painting. You can always pour the leftover back into cans. For large jobs, use the bucket and a roller screen rather than a roller tray. It’s much faster to load your roller with the screen than to use a roller pan. Simply dunk the roller into the paint bucket, then roll it along the screen until it stops dripping.
When you go to the home improvement store, find out how much 12 gallons of the paint you want would cost, and that will help you determine your cost. Maybe it's a low-quality paint that costs $30, in which case you're looking at about $360 for paint. If you choose high-quality paint that costs around $70, your total paint cost could be closer to $840. Professionals also recommend that you add an extra 10 or 20 percent to your total square footage, depending on the type of siding you have. Some textures require extra paint because they're rough. This is especially true with wood and stucco siding.
Picking exterior house paint colors is a lot different than picking a color for a shirt or a car.  It may help to drive around to observe colors that other homeowners have combined on homes that are of similar size and design as yours.  There are also online resources that provide homeowners with the ability to create virtual makeovers of their home by combining colors together through their software programs as well.
To win work, contractors generally have to bid against other suppliers. To make an accurate bid, they estimate the time and materials required to complete the job. They measure the area to be painted and discuss the type of finish the customer requires. They assess the quality of the surfaces to work out how much remedial work they must carry out before painting. They might have to remove old paint or wall coverings, or repair cracks and other damage. They also calculate the cost of any essential equipment, such as scaffolding for exterior walls.

House Painter

×